Sunday, June 27, 2010

BitTorrent Client: Transmission on DD-WRT

If you've followed the previous guides to set the opkg system, then installing transmission on the USB enabled DD-WRT system is a no-brainer. Only one little thing needs to be taken care of...

  1. Install transmission
    To do so, Use PuTTY to log in and run the command below:
    opkg install transmission-web

    This will install libevent(required library) transmission-daemon(the actual program) and transmission-web(the web interface).

  2. Setup transmission
    Run
    transmission-daemon
    wait for 10 seconds then stop it:
    killall transmission-daemon

    This will create default configuration file for transmission, the file is located at /mnt/root/.config/transmission-daemon/settings.json
    Edit this file with following(delete all previous contents)

    {
    "blocklist-enabled": 1,
    "download-dir": "\/mnt\/share\/torrents",
    "download-limit": 100,
    "download-limit-enabled": 1,
    "encryption": 2,
    "max-peers-global": 35,
    "peer-port": 25000,
    "pex-enabled": 1,
    "port-forwarding-enabled": 1,
    "rpc-authentication-required": 0,
    "rpc-password": "",
    "rpc-port": 9091,
    "rpc-username": "",
    "rpc-whitelist": "192.168.1.*",
    "upload-limit": 200,
    "upload-limit-enabled": 1
    }


    Above is taken from DD-WRT wiki with some modification. Also create the download folder
    mkdir -m 777 /mnt/share/torrents

    So now all configure files for transmission are in /mnt/root/.config(or /tmp/root/.config, its the same). Downloaded files will be in /mnt/share/torrents

  3. Set transmission for web access
    This is usually not a problem, however, in our setup, the web pages is are in non-standard location. So we must let transmission aware of the change.

    To do so, a variable must be set for transmission. Run the command lines below:
    export TRANSMISSION_WEB_HOME='/opt/usr/share/transmission/web/'
    transmission-daemon

    Now access transmission web manage interface at http://ip_of_the_router:9091/
    If everything works out, move to next step.

  4. Run it as service
    To do so, add the following line to /mnt/root/.profile

    export TRANSMISSION_WEB_HOME='/opt/usr/share/transmission/web/'

    Then create the startup script /opt/etc/init.d/transmission(delete all previous contents if its not empty)

    source /mnt/root/.profile
    killall
    transmission-daemon
    sleep 2
    transmission-daemon -g /mnt/root/.config/transmission-daemon/


    Set it to run as service:
    chmod a+x /opt/etc/init.d/transmission
    ln -s /opt/etc/init.d/transmission /opt/etc/init.d/S60transmission

77 comments:

Zach said...

Would you consider doing a post/walking me through setting this up with rss downloading? The g300nh is my first DD-WRT and linux experience and i'm trying to transition over from my windows 7 machine doing all the work to my router so I can start cutting it off when not in use. I have uTorrent setup to auto-download all my TV shows and Event Ghost managing everything the movement and renaming of everything. I'd like to get DD-WRT handling all this and DLNA streaming to my Xbox 360's and other media machines.

Zach said...

I've been trying to incorporate blocklists into my transmission setup. I've hacked together a startup script from pieces I've found on the dd-wrt forums. here's what I've done:

nano /opt/etc/init.d/transmission

source /mnt/root/.profile
killall transmission-daemon
sleep 2

# update blocklist
echo "updating blocklist"
cd /mnt/root/.config/transmission-daemon/blocklists
wget -q http://www.bluetack.co.uk/config/level1.gz
if test -f level1.gz; then
rm level1
gunzip level1.gz
chmod go+r level1
fi
# start transmission
echo "starting transmission"
transmission-daemon -g /mnt/root/.config/transmission-daemon/

See anything wrong with this?

Anonymous said...

Using Transmission on this router slows it down to a crawl. The memory usage on the router goes to 100% (even with low download rates of under 100KB/s and under 10 simultaneous connections). Perhaps enabling swap space could improve this issue?

Anonymous said...

Weird, I have no issues with transmission running 6 simultaneous speedy downloads/uploads on openwrt backfire. Yes, memory usage goes to 100%, but in ssh , run top and see most of it is cache (I suppose for writing/reading files). The issue for me is when transmission is rechecking files at the start, and that is because it uses almost 100% cpu.

To prevent it rechecking everytime I reboot my router, I used this in my script for shutdown and call it in my shutdown script before unmounting the usb drive (ex: ./MYtransmission stop)
Be sure to set up password access to the transmission-web interface so it can run these commands.

#!/bin/sh /etc/rc.common


start() {

transmission-daemon -g /mnt/usb/transmission-daemon
sleep 3
username='your user'
password='your password'
transmission-remote 8891 --auth $username:$password -tall -s
}

stop() {
username='your user'
password='your password'


transmission-remote 8891 --auth $username:$password -tall -S
sleep 10
killall transmission-daemon
}

restart() {
stop; sleep 5; start
}

Zach said...

Is this normal?

Mem: 38008K used, 23560K free, 0K shrd, 2460K buff, 22184K cached
Mem: 42972K used, 18596K free, 0K shrd, 2736K buff, 25004K cached
CPU: 0% usr 0% sys 0% nic 100% idle 0% io 0% irq 0% sirq
Load average: 0.00 0.00 0.00 1/37 11555
PID PPID USER STAT VSZ %MEM %CPU COMMAND
1715 1714 root S 7960 13% 0% transmission-daemon
1734 1714 root S 7960 13% 0% transmission-daemon
1713 1 root S 7960 13% 0% transmission-daemon
1714 1713 root S 7960 13% 0% transmission-daemon
1207 1 root S 2544 4% 0% httpd -p 80
9301 1494 root S N 2304 4% 0% /usr/sbin/smbd -s /opt/etc/samba/smb.
1494 1 root S N 2128 3% 0% /usr/sbin/smbd -s /opt/etc/samba/smb.
653 1 root S 1448 2% 0% watchdog
778 1 root S 1412 2% 0% resetbutton
11555 1697 root R 1352 2% 0% top
940 1 root S 1104 2% 0% ttraff
1338 1 root S 1104 2% 0% process_monitor
2474 949 root S 1084 2% 0% dropbear -b /tmp/loginprompt -r /tmp/
9598 949 root S 1084 2% 0% dropbear -b /tmp/loginprompt -r /tmp/
1 0 root S 1032 2% 0% /sbin/init
2475 2474 root S 1020 2% 0% -sh
1697 924 root S 1020 2% 0% -sh
924 1 root S 1008 2% 0% telnetd
9599 9598 root S 1008 2% 0% sh -c /usr/libexec/sftp-server
949 1 root S 1008 2% 0% dropbear -b /tmp/loginprompt -r /tmp/

leo.d said...

Lots of files are cached and that's normal, nothing to worry about. About rss downloading, sorry I don't use this feature at all so I'm not sure how to do that...

Zach said...

What concerns me is that it appears that things are running multiple times, I've got top running in a different terminal so I can see, and sometimes there are 5 listings for transmission-daemon and other things. Just want to make sure i'm not running things multiple times somewhere and wasting precious resources =)

Eddo said...
This comment has been removed by the author.
Eddo said...

Transmission isn't running stable on my Atheros based TP-Link TL-WR1043ND with DD-WRT v24-sp2 (04/23/10) std - build 14311. I used a Broadcom based Asus before. On this I could run a swap file. Now it seems this feature is no longer supported in dd-wrt, so I can't re-create my former setup. Any suggestions?

As I reïnstalled everything using these excellent tutorials I appeared that the blocklist file is no longer available on www.bluetack.co.uk. I changed my script to this:
#!/bin/sh

# update blocklist
cd /mnt/root/.config/transmission-daemon/blocklists/

wget -q http://firsta.googlepages.com/level1.gz
if test -f level1.gz; then
rm level1
gunzip level1.gz
chmod go+r level1
fi

source /mnt/root/.profile

if [ -n "`pidof transmission-daemon`" ]; then
kill -9 `pidof transmission-daemon`
fi

sleep 2

/opt/usr/bin/transmission-daemon -g /mnt/root/.config/transmission-daemon/ -gsr 1.0 -b

Anonymous said...

Good Tutorial. I enjoy reading it.
Do u know how to make the scheduler work too in DDWRT Transmission?

Anonymous said...

THX!
In the last 3 days I tried install transmission on ddwrt, but without a success. Thaks to you, now working perfectly!
Andrew

ccdoggy said...

I am having a problem with the config file. I delete everything out of the created one and then paste in that config you have here. It seems to be over-written when i start transmission so it goes back to the default values.

I ended up just modifying the stock one to the settings i require and it seems to be working excellent!

Isanderthul said...

@ccdoggy you can only modify the config file when the transmission-daemon is not running

a better script is the following, especially if you want to use cron to start and stop the service at certain times...

root@android /mnt $ cat /opt/etc/init.d/transmission
#!/bin/sh
source /mnt/root/.profile
sleep 2
SERVICE='transmission-daemon'
if ps ax | grep -v grep | grep $SERVICE > /dev/null
then
echo "$SERVICE service running, everything is fine"
else
echo "$SERVICE is not running"
echo "starting $SERVICE"
transmission-daemon -g /mnt/root/.config/transmission-daemon/
fi

you can start and stop automatically using cron if you put the following in the ddwrt web administration, commands, startupscript.
/bin/sh -c 'echo "# minute (0-59)," >> /tmp/crontab'
/bin/sh -c 'echo "# | hour (0-23)," >> /tmp/crontab'
/bin/sh -c 'echo "# | | day of the month (1-31)," >> /tmp/crontab'
/bin/sh -c 'echo "# | | | month of the year (1-12)," >> /tmp/crontab'
/bin/sh -c 'echo "# | | | | day of the week (0-6 with 0=Sunday)." >> /tmp/crontab'
/bin/sh -c 'echo "# | | | | | commands" >> /tmp/crontab'
/bin/sh -c 'echo "# check if running every 5 minutes until 20:00 every day" >> /tmp/crontab'
/bin/sh -c 'echo " */5 0-20 * * * root /opt/etc/init.d/transmission" >> /tmp/crontab'
/bin/sh -c 'echo "# check not running between 20:00 and 21:00" >> /tmp/crontab'
/bin/sh -c 'echo " */5 20-21 * * * root killall transmission-daemon" >> /tmp/crontab'
/bin/sh -c 'echo "# check if running every 5 minutes after 21:00" >> /tmp/crontab'
/bin/sh -c 'echo " */5 21-23 * * * root /opt/etc/init.d/transmission" >> /tmp/crontab'

Anonymous said...

You have to open up port 25000, right?

/usr/sbin/iptables -I INPUT 1 -p tcp --dport 25000 -j logaccept

Eddo said...

I found that the blocklist I used in my script is outdated. I advise users to change to use the blocklist http://download.m0k.org/transmission/files/level1.gz

Anonymous said...

hello, first of all great job with the blog, i really appreciate all the tutorials. second of all, is there any way to enable swap on the device?

i get a "function not implemented" error when trying to use swapon

Jordan said...

Hey all - I just followed all of these tutorials with success. I'd just like to comment about the problem of swap files:

I've looked into it pretty extensively. What it comes down to ( I believe..) is that there's no loopback support native to the "hybrid" system we're all creating with WZR-HP-G300HN + DD-WRT + openWRT opkg system. You can download kmod-loop and attempt to install it, but it will fail. I've even extracted the module itself (loop.ko) and attempted to force-insert it into the kernel "insmod loop.ko -f", but I get a "bad format" error.

Also, something to note is that I'm running kernel version 2.6.24.111 while opkg packages are all for kernel version 2.6.32.24. So, what I'm thinking is that while we can install opkg programs, installing any kernel-related stuff form opkg will totally fail. Also, /etc/functions.sh is missing.

Bottom line: It doesn't look like we can get swap files just yet.

kj said...

transmission-daemon overwrites the settings.json every time it starts :( ???

Dan said...

Should be nice to add also a guide to aMule, in any case the big issue to solve i the correct port fowarding on the local ports. To be sure that aren't dropped by the firewall is to place the rules at the very top of INPUT chain using the following command:

iptables -I INPUT 1 -p tcp --dport 4662 -j ACCEPT
iptables -I INPUT 1 -p udp --dport 4665 -j ACCEPT
iptables -I INPUT 1 -p udp --dport 4672 -j ACCEPT

Dan said...

Has been developed a nice remote-gui for Windows that permit the control of torrents. The apps, that works even as standalone torrent client, can be found here:

http://www.sb-innovation.de/f93/transmission-1-76-windows-17975/

Mark said...

A better link for a transmission remote GUI. It is for all platforms!

http://code.google.com/p/transmisson-remote-gui/downloads/

Greg said...

Has anyone tried to get this to work through an Android remote client? I can't get it to work on a remote network. It will only work locally, despite all sorts of port forwarding and whitelisting.

Greg said...

Figured it out. Port forwarding will not open ports internal to the router. Thus, Transmission only listens to requests on its port from the internal LAN.

The following command in your firewall script (Administration, Commands) will enable external (web) control of your Transmission client.

iptables -I INPUT -p tcp --dport 9091 -j logaccept

Mark said...

If enabling transmission access from outside your LAN, enable user log-in by adding the -t option to the run command.

transmission-daemon -t -b -g /mnt/root/.config/transmission-daemon/

set username with -u and pass with -v
transmission-daemon -u user
transmission-daemon -v pass

Anonymous said...

Sorry, I tried to install transmission, but when I launch transmission-daemon, the router reply this code "transmission-daemon: symbol 'errno': can't handle reloc type 0x2f".. Why?

Ah, when I installed openwrt, I've not updated the libc, otherwise opkg doesn't work! Could be a problem?

Thank you very much!!

P.S. I'm italian, sorry for my bad english =)

Anonymous said...

Hey,

When trying to install a receive this error:

root@DD-WRT root $ opkg install transmission-web
Collected errors:
* opkg_install_cmd: Cannot install package transmission-web.
root@DD-WRT root $

Any Ideas?

Anonymous said...

try
opkg update

ViperSBT said...

Man, this was a huge help and got me up and running... Question, what is the easiest way to add torrents? I tried AutoTrans but it doesn't like sites requiring authentication... Which is leading me to think that I need a Watch Directory. I went to the config details on Transmission and found how to set a directory and enable it, but when I do that it won't let me start the daemon... Any thoughts?

jeyaganesh.n said...

Thanks to you, I have followed all the steps and got transmission working, on 300 NH.

Do i have to plug the USB disk 24 x 7. I want to remove it, whenever i don need transmission.

How can i do this ?

Jake said...

running transmission-daemon goes fine, however whenever I 'killall transimission-daemon' it says no processes were killed, implying it didn't start. Any ideas why this would be?

Anonymous said...

hi do we need to open port :

/usr/sbin/iptables -I INPUT 1 -p tcp --dport 25000 -j logaccept
?
even with upnp on? just asking

if so, put it into init.d or start script right? thanks.

Anonymous said...

My transmission doesn't seem to be very stable. It runs for about 30 min. and then ssh and web server goes down.

I can't login to my router through web nor ssh. However, internet still work properly.

Are there anyway to diagnose this problem? Where can I find the log file that might give me some ideas what went wrong?

Thanks

Leandro said...

hello all, getting the same problem here in my TP-1043ND:

When I launch transmission-daemon, the router reply this code "transmission-daemon: symbol 'errno': can't handle reloc type 0x2f"..

All the packages seems to be installed correctly but for some reason, transmission cannot start.

Anonymous said...

I get the same issue as Leandro, i also rebooted and tried to install the package again and it said that it was up to date

Anonymous said...

@Leandro and anonymous

I'm also using 1043nd. Everything works fine. Did you change the opkg.conf in "Software Installation on DD-WRT -- Part 1"? I had the reloc 0x2f problem but fixed it when I edited the opkg.conf as recommended by ccdoggy in the comments section.

NoOne said...

Jake, I'm having the same problem as you.

I've installed transmission, run "transmission-daemon" and then when I run "killall transmission-daemon" it sais that "no process killed".

As I understand, this problem occours because transmission-daemon have not been started. But I don't know why...

Does anyone have any idea or can try to help us!?

Thanks at all!

NoOne said...

I was just figuring out if the problem can be related to my disk because the USB disk is formatted in NTFS, not EXT3.

The current version of DD-WRT support NTFS partition, but I'm not sure if transmission also works well with it.

Can anyone help me!?

Thanks

Mathew H said...

What the hells wrong with you people make a script we can run form ddwrt for christs sake

NoOne said...

I solved my problem. Just used an updated version of transmission

Anonymous said...

how?

Anonymous said...

The version of transmission posted here isnt very stable (2.04). But i cant figure out how to update for a newer one.
Any ideas?

Anonymous said...

I'm having the same problem.
The process doesn't start.
Running transmission-daemon -f i get segmentation fault
Any suggestion?

chain710 said...

running transmission-daemon -f on NH2, i got segment fault.
Any ideas?

mauka said...

Hi,

How is the upgrading of the client possible?

Transmission Hollywood FL said...

Transmission Hollywood FL provide you with a complete estimate and an explanation of all repairs to be performed. Our work is 100% guaranteed.

Birkhahn said...

I have Problem:


root@Powermonster-Router root $ opkg install transmission-web
Installing transmission-web (2.50-2) to root...
Downloading http://downloads.openwrt.org/snapshots/trunk/ar71xx/packages//transmission-web_2.50-2_ar71xx.ipk.
Installing transmission-daemon (2.50-2) to root...
Downloading http://downloads.openwrt.org/snapshots/trunk/ar71xx/packages//transmission-daemon_2.50-2_ar71xx.ipk.
Installing libcurl (7.23.1-1) to root...
Downloading http://downloads.openwrt.org/snapshots/trunk/ar71xx/packages//libcurl_7.23.1-1_ar71xx.ipk.
Installing libopenssl (1.0.0g-1) to root...
Downloading http://downloads.openwrt.org/snapshots/trunk/ar71xx/packages//libopenssl_1.0.0g-1_ar71xx.ipk.
Installing zlib (1.2.5-1) to root...
Downloading http://downloads.openwrt.org/snapshots/trunk/ar71xx/packages//zlib_1.2.5-1_ar71xx.ipk.
Installing libpthread (0.9.33-103) to root...
Downloading http://downloads.openwrt.org/snapshots/trunk/ar71xx/packages//libpthread_0.9.33-103_ar71xx.ipk.
Installing libevent2 (2.0.16-1) to root...
Downloading http://downloads.openwrt.org/snapshots/trunk/ar71xx/packages//libevent2_2.0.16-1_ar71xx.ipk.
Installing librt (0.9.33-103) to root...
Downloading http://downloads.openwrt.org/snapshots/trunk/ar71xx/packages//librt_0.9.33-103_ar71xx.ipk.
Installing libminiupnpc (1.6-1) to root...
Downloading http://downloads.openwrt.org/snapshots/trunk/ar71xx/packages//libminiupnpc_1.6-1_ar71xx.ipk.
Configuring libpthread.
Configuring zlib.
Configuring libopenssl.
Configuring libcurl.
Configuring libevent2.
Configuring librt.
Configuring libminiupnpc.
Configuring transmission-daemon.
Configuring transmission-web.
root@Powermonster-Router root $ transmission-daemon
root@Powermonster-Router root $ killall transmission-daemon
killall: transmission-daemon: no process killed

The Transmission-Daemon not run?

Eduardo said...

I'm also having this segmentation fault while trying to run transmission-daemon in foreground.
If someone find a answer, please leave the answer.

Anonymous said...

Eduardo, try this:

cp /lib/libnvram.so /opt/lib/libnvram.so
mount -o bind /opt/lib /lib
transmission-daemon –f

And let me know ;)

Anonymous said...

After:
cp /lib/libnvram.so /opt/lib/libnvram.so
mount -o bind /opt/lib /lib
transmission-daemon –f

Transmission 2.50 (13228) started!!

Birkhahn said...

How do I create a startup script? (Under DD-WRT's web interface, Administration-> Commands)
Currently it is:

#!/bin/sh

sleep 5
#mount -t ext3 -o noatime /dev/discs/disc0/disc /mnt
mount -t ext3 -o noatime /dev/discs/disc0/part1 /mnt
#choose one for your drive, see Step #6

sleep 2
if [ -f /mnt/optware.enable ]; then
mount -o bind /mnt/etc /etc
mount -o bind /mnt/root /tmp/root
mount -o bind /mnt/opt /opt
else
exit
fi

if [ -d /opt/usr ]; then
export LD_LIBRARY_PATH='/opt/lib:/opt/usr/lib:/lib:/usr/lib'
export PATH='/opt/bin:/opt/usr/bin:/opt/sbin:/opt/usr/sbin:/bin:/sbin:/usr/sbin:/usr/bin'
else
exit
fi
chmod a+x /opt/etc/init.d/transmission
ln -s /opt/etc/init.d/transmission /opt/etc/init.d/S60transmission

How do I add it?

Eduardo said...

Yes. That works. Thank you.

Anonymous said...

anonymous, thank you for your tip on segment fault! saved me so much time

jim smith said...

The current version of DD-WRT support NTFS partition, but I'm not sure if transmission also works well with it.
Transmission Repair Hollywood FL

VITOR said...

Same problem of unstability. I can't get SSH, SMB or Web access after a random amount of time. Wireless and LAN still working after this. I think it's a RAM problem, because Transmission is a very memory hungry application on this router. I can't get swap working, "Function not implemented" error.

Any ideas?

VITOR said...

Figured it out: USB HDD was disconecting... Just replaced the drive and everything worked flawlessly.

timeless said...

"mount -o bind /opt/lib /lib" (suggested in a comment here to fix seg error) broke my webgui -rebooting fixed it.

this did the trick though:
http://www.dd-wrt.com/phpBB2/viewtopic.php?p=749875#749875

jim smith said...

My transmission doesn't seem to be very stable.
Transmission Hollywood FL

jamshad hashmi said...

BITTORRENT DOWNLOAD FREE SOFTWARE PLUS LATEST AND FULL VERSION

crack software said...

totally supported and solve my problem
nice blog and nice saying about habits and really amazing tips ,

crack software said...

i appreciate you , i read your blog , totally supported and solve my problem
nice blog and nice saying about habits and really amazing tips , so i decided to salute you for this beautiful articles

javed Akmal said...

Fantastic website. Lots of helpful information here..
And obviously, thanks for your sweat!
Nitro Pro 9 Crack

Best Antivirus 2016 said...

You wrote a good solution of problem.. Thanks for adding the detailed solution of it..

AVG Antivirus 2016

Yousaf Bhatti said...

Should you be thinking of writing a blog, this information has some good concepts to assist you make something great. Regardless of whether you need to make money with it, or simply just communicate with your loved ones, operating a blog might be a wonderful approach to conversation. Read on to understand how to make the most of your running a blog practical experience.

Windows 10 Activator Crack 64 Bit
Artlantis Studio 5 Activation Code

Yousaf Bhatti said...

I’m extremely pleased to discover this great site.
I want to to thank you for ones time for this particularly wonderful read!!
I definitely enjoyed every little bit of it and i also have you saved
as a favorite to check out new stuff on your web site

WinZip 20 Pro Activation Key
Adobe Acrobat Reader DC 2015 Product Key

Yousaf Bhatti said...

I’m extremely pleased to discover this great site.
I want to to thank you for ones time for this particularly wonderful
read!!
I definitely enjoyed every little bit of it and i also have you saved
as a favorite to check out new stuff on your web site


WinX HD Video Converter Deluxe Giveaway


Cyberghost VPN 5 Activation Key

Adobe Photoshop CC 2015 Crack

Yousaf Bhatti said...

Windows 10 Activator Crack 64 Bit
Artlantis Studio 5 Activation Code
Windows XP Vienna Edition SP3 ISO
Adobe Acrobat Reader DC 2015 Product

Key

Mapinfo Professional 12.5 Crack
SpotyDL Pro Crack
Driver Detective Crack 9.0.0.23
Facebook Hacker Pro
Adobe Photoshop CC 2015 Crack
CyberGhost VPN 5 Crack
AVS Video Editor 6.5 Activation key
WinZip 20 Pro Activation Key
Adobe Photoshop CC 2015 Crack

Yousaf Bhatti said...

so nice your performance is so capable to admire..
IPTV Pro
Club .Penguin

Yousaf Bhatti said...

It’s actually a great and helpful piece of info.
I’m happy that you shared this helpful information with us.
Please stay us informed like this. Thanks for sharing.
Macx Video Converter [v5.0.8] Key
Uniblue Driver Scanner v6.1.0 Crack
iCountTimer Pro
Capture One Pro 9 Crack

Shahzad said...

I love your blog.. very nice colors & theme. Did you design this website yourself or did you hire someone to do
it for you? Plz answer back as I’m looking to create my own blog and would
like to know where u got this from. thanks....

Max Uninstaller 3.6 Crack

Shahzad said...

I love your blog.. very nice colors & theme. Did you design this website yourself or did you hire someone to do
it for you? Plz answer back as I’m looking to create my own blog and would
like to know where u got this from. thanks



Windows 8 Product Key Generator

Shahzad said...

I love your blog.. very nice colors & theme. Did you design this website yourself or did you hire someone to do
it for you? Plz answer back as I’m looking to create my own blog and would
like to know where u got this from. thanks





AVS Video Converter 8.5 Crack

Shahzad said...

I love your blog.. very nice colors & theme. Did you design this website yourself or did you hire someone to do
it for you? Plz answer back as I’m looking to create my own blog and would
like to know where u got this from. thanks


Panda Antivirus Pro 2016 Keygen

Sulena Mowmoline said...

Hi admin its final and best solution for me. thanks for working on it. all information about future of SEO is final and best information. thanks keep it up all the time.
windows 7 all in one iso

linksoflondonu said...


microsoft outlook 2010 product key activation code , window 7 activation key , windows 10 activation 0x80072f8f , win7 sp1 activation key buy , windows 7 online key , windows 7 ult sp1 keys retail , windows 10 pro key sale , win7 home premium sp1 urun anahtarı , lSW6ed

cheap office 2016 product key

Online Windows Server 2012 R2 Essentials Product Key

Cheap Rosetta Stone French Level 1, 2, 3, 4, 5 Set Key Sale

windows 10 product serial number offer

buy office 2013 product serial number

linksoflondonu said...


microsoft outlook 2010 product key activation code , window 7 activation key , windows 10 activation 0x80072f8f , win7 sp1 activation key buy , windows 7 online key , windows 7 ult sp1 keys retail , windows 10 pro key sale , win7 home premium sp1 urun anahtarı , lSW6ed

cheap office 2016 product key

Online Windows Server 2012 R2 Essentials Product Key

Cheap Rosetta Stone French Level 1, 2, 3, 4, 5 Set Key Sale

windows 10 product serial number offer

buy office 2013 product serial number

Funny Videos said...


Done well. I am astounded with the standard of the data offered. I sincerely hope that you keep up with the fantastic job accomplished.

MICROSOFT OFFICE PROFESSIONAL PLUS 2013 PRODUCT KEY

Dua Ahmad said...

I think it's a RAM problem, because Transmission is a very memory hungry application on this router. I can't get swap working, "Function not implemented" error.
Abbyy Finereader 14 Pro

Post a Comment